T. Nexus Engineering Indonesia, An Established Oil and Gas Support and marine Company invites suitable qualified candidates to fill the following position:
Commercial Supervisor
- Female
- Diploma or University graduated
- Able to speak and write mandarin and English
- Good working attitude & Able to work independently with high integrity
- Preferably knowledge computer literate windows / office
- Fresh grads with outstanding academic are welcome
Please Apply Online!
Only short candidate will be notified. Please send your application before 10 May 2008.
I hope join with your company soon
Dear Sir/Madam,
With this letter, allow me to apply for position of Commercial Supervisor in PT Nexus Engineering Indonesia.
I am ismadi,ST, 30 year old, Meried, graduate of Bacelor’s Degrees
Department Mecanical Engineering, Universitas Batam (UNIBA). I was
graduate at 2002 with 2,70 of GPA. I have ability to operate some
computer program like Microsoft office, excel,power point,MS word
As consideration, I enclose also resume of me, and I attach picture in
my resume, working experience.
I hope my qualifications and my ability merit your consideration and
look forward to your reply. I hope I am able to follow carried out
selection steps and also can get away to become an employee at PT Nexus Engineering indonesia
Yours faithfully,
Ismadi,ST
C U R R I C U L U M V I T A E
Experiences
July 2006 – At present PT Sanmina- SCI-Batam
As Senior Asst Engineer Process
Sanmina-SCI is the word wide PCBA manufacturing company
• Yield from SMT ~ Finish good responsibility
• Drive the pilot run as well
• As the leader for the project transfer
• Process improvement
• DFM generation for any deviation design or process capability issue
• Driver of FA (First Article) product, In term of :
• L iase with the customer
• Define the process Flow Chart
• Generate Lot Traveler
• Work Instruction generation (PCB Preparation ~ Packing/Shipment)
• Control of direct and Indirect material
• FA qualification report
• Drive the improvement of Quality (Process capability and defect per million) and Process Yield.
• Drive continuous improvement projects (e.g. cost reduction)
• Provide support on the start-up, set-up and qualification of new incoming equipments and materials before being used by production.
• Responsible in performing process parameters optimization with statistical approach (e.g. Design of Experiment).
• Responsible in setting up the SPC at every critical process point.
• Responsible in analyzing the defective products returned by the customer and perform investigation through an 8-D (8-Discipline)
• Liase with supplier and other Dept as part of continuous improvement
Working instruction draft and release to production
ECN follow up and implementation
June 2004 – June 2006 PT PLEXUS MFG Indonsia-Batam
PCBA manufacturing Company
Senior SMT Technician
Responsibilities:
Controling Spare part to be reported to superrior
Release/ updating document of standard operation procedure.
Setup and prepare for new model.
Handle all SMT document and data collection.
As the leader for all Technician Incharge.
Reporting to superrior about pevormance and improvement of the machine and utilization for daily,weekly,mounthly,quarterly and yearly to keep good conditionof the machine according standard ISO 9002.
July 2000 – April 2004 PT. Schneider Electric - Batam
SMT Technician
Responsibilities:
• Incharge and maintenance of machine performance.
• Monitoring of machine performance and throuble shotting
• Maintain of yield as good condition
• Monitoring production machine as whell.
Setup and prepare for new model.
July 1997 – july 2002 PT. Epson - Batam
SMT Technician
Responsibilities:
• Incharge and maintenance of machine performance.
• Monitoring of machine performance and throuble shotting
• Maintain of yield as good condition
• Monitoring production machine as whell.
Setup and prepare for new model.
Trainings attended
• PANASERT Chip and IC mounter internal Training 03th–08th July 1997 at PT EPSON BATAM.
• YAMAH Chip and IC mounter internal Training 17th–22th July 2000 at PT EPSON BATAM.
• In House Traning of PLC 26th – 2 th December 2002 at PT.Schneider Electric - Batam
• Juki Chip and IC Mounter Training 12th-17th June 2002 at PT.Schneider Electric – Batam.
• Vitronic Delta Wave Soldering 04th – 09th November 2002 at PT.Schneider Electric – Batam.
• Fuji Chip and IC mounter internal training 20th – 25th August 2004 at PT.PLEXUS MANUFACTURING INDONESIA-BATAM
• Siplace advance level 1 19th – 23 th September 2005 at SIEMENS CENTER - Singapore
Education 2002: Graduate Bachelor’s Degree from ‘’ UNIVERSITY BATAM ‘’ (UNIBA) Department of Mecanical Engineering.
Others
• Fluent in English (Oral and Literal),Malay and Bahasa Indonesia
• Good in Microsoft Office (MS Excel, Power Point and MS Word)
• GC-Prevue
Reference: Mr.Abarques Layag Junell
Snr.Manufacturing Engineer
Hp : +62 813 6498 3466
Phone : +62-770 612 666 Ext 794
Pasport Number AJ-274166
Interest : Sport,Muzik, and General knowledge